N364497

U.S. Department of Homeland Security U.S. Customs and Border Protection National Commodity Specialist Division One World Trade Center, Suite 51.201 New York, NY 10007 U.S. Customs and Border Protection N364497 September 4, 2026 CLA-2-85:OT:RR:NC:N2:220 CATEGORY: Origin Martin Robles K&K Interational Logistics 555 West Goldhill Road, Suite 32 Nogales 85648 RE: The tariff classification, country of origin and marking of automotive wiring harnesses Dear Mr. Robles: In your letter dated August 22, 2026, you requested a ruling on behalf of your client, EDS Manufacturing, Inc. This request covers five automotive wiring harness assemblies, identified by part numbers 2HH11-H994B-RH, 2HH11-K138B-RH, 2WH11-K015D, 2WH11-L8710, and 2WH12-L002B-LH. These assemblies consist of individually insulated electrical conductors bundled together, terminals, connector housings, seals, tubing, tape, grommets, splices, and related protective components. In use, these wiring harnesses provide electrical connectivity between various vehicle components. While each harness varies in function, layout, and complexity, the manufacturing process for all five is identical and follows these steps: Insulated cable conductors are manufactured in Mexico and shipped to El Salvador in bulk. Additional components, including terminals, connector housings, seals, tubing, tape, grommets, and splices, are sourced in El Salvador or imported from the United States, Mexico, China, Japan, Thailand, or Malaysia. In El Salvador, cables are cut to length, stripped, and crimped with terminals. Seals, grommets, heat-shrink tubing, and tape are applied according to individual harness specifications. The cables are then routed, bundled, and wrapped in protective tubing. After additional connectors and protective components are installed, the harnesses undergo electrical testing and inspection before being prepared for export to Mexico. In Mexico, the harnesses undergo final electrical testing and a dimensional inspection of critical characteristics. If necessary, the harnesses are reworked to meet specifications before being packaged for export to the United States. Classification You suggest the correction tariff classification for all five items is 8544.30.0000, Harmonized Tariff Schedule of the United States (HTSUS). We agree. The applicable subheading for all five automotive wiring harness assemblies will be 8544.30.0000, HTSUS, which provides for “Insulated (including enameled or anodized) wire, cable (including coaxial cable) and other insulated electric conductors, whether or not fitted with connectors; optical fiber cables, made up of individually sheathed fibers, whether or not assembled with electric conductors or fitted with connectors: Ignition wiring sets and other wiring sets of a kind used in vehicles, aircraft or ships.” The general rate of duty will be 5 percent ad valorem. The duties cited above are current as of this ruling’s issuance. Duty rates are provided for your convenience and are subject to change. The text of the most recent HTSUS and the accompanying duty rates are provided at https://hts.usitc.gov/. This ruling does not address the applicability of any additional duties, taxes, fees, exactions and/or other charges, which may apply to the goods discussed herein. This includes, but is not limited to, tariffs and other duties as provided for in Subchapter III to Chapter 99, HTSUS. Thus, for example, in addition to the classification stated above, the merchandise covered by this ruling may also need to be reported with either the Chapter 99 provision under which an additional tariff applies or one of the Chapter 99 provisions covering exceptions to such tariffs. For further information to assist with the importation process, please refer to the frequently updated Cargo Systems Messaging Service (CSMS) messages at https://www.cbp.gov/trade/automated/cargo-systems-messaging-service and the Trade Remedies page at https://www.cbp.gov/trade/programs-administration/trade-remedies. Country of Origin When determining the country of origin for purposes of applying current trade remedies under Section 301 and additional duties, the substantial transformation analysis is applicable. See, e.g., Headquarters Ruling Letter H301619, dated November 6, 2018. The test for determining whether a substantial transformation will occur is whether an article emerges from a process with a new name, character, or use different from that possessed by the article prior to processing. See Texas Instruments Inc. v. United States, 681 F.2d 778 (C.C.P.A. 1982). This determination is based on the totality of the evidence. See National Hand Tool Corp. v. United States, 16 C.I.T. 308 (1992), aff’d, 989 F.2d 1201 (Fed. Cir. 1993). Additionally, Section 304 of the Tariff Act of 1930, as amended (19 U.S.C. 1304), provides that unless excepted, every article of foreign origin imported into the United States shall be marked in a conspicuous place as legibly, indelibly, and permanently as the nature of the article (or its container) will permit, in such a manner as to indicate to the ultimate purchaser in the United States, the English name of the country of origin of the article. Congressional intent in enacting 19 U.S.C. 1304 was “that the ultimate purchaser should be able to know by an inspection of the marking on the imported goods the country of which the goods is the product. The evident purpose is to mark the goods so that at the time of purchase the ultimate purchaser may, by knowing where the goods were produced, be able to buy or refuse to buy them, if such marking should influence his will.” See United States v. Friedlaender & Co., 27 C.C.P.A. 297, 302 (1940). Part 134 of the U.S. Customs and Border Protection (“CBP”) Regulations (19 CFR 134) implements the country of origin marking requirements and exceptions of 19 U.S.C. 1304. Section 134.1(b), CBP Regulations (19 CFR 134.1(b)), defines “country of origin” as the country of manufacture, production, or growth of any article of foreign origin entering the United States. Further work or material added to an article in another country must effect a substantial transformation in order to render such other country the “country of origin” within the meaning of the marking laws and regulations. Section 304 of the Tariff Act of 1930, as amended (19 U.S.C. 1304), provides that unless excepted, every article of foreign origin imported into the United States shall be marked in a conspicuous place as legibly, indelibly, and permanently as the nature of the article (or its container) will permit, in such a manner as to indicate to the ultimate purchaser in the United States, the English name of the country of origin of the article. Congressional intent in enacting 19 U.S.C. 1304 was “that the ultimate purchaser should be able to know by an inspection of the marking on the imported goods the country of which the goods is the product. The evident purpose is to mark the goods so that at the time of purchase the ultimate purchaser may, by knowing where the goods were produced, be able to buy or refuse to buy them, if such marking should influence his will.” See United States v. Friedlaender & Co., 27 C.C.P.A. 297, 302 (1940). Section 134.1(b), CBP Regulations (19 CFR 134.1(b)), defines “country of origin” as the country of manufacture, production, or growth of any article of foreign origin entering the United States. Further work or material added to an article in another country must effect a substantial transformation in order to render such other country the “country of origin” within the meaning of the marking laws and regulations. Regarding the origin of the automotive wiring harness assemblies, it is the opinion of this office that the insulated copper wire conductor manufactured in Mexico imparts the character of the finished automotive wiring harness assemblies as it is the functional component of the assemblies. Further, the assembly processes completed in El Salv

is applicable. See, e.g., Headquarters Ruling Letter H301619, dated November 6, 2018. The test for determining whether a substantial transformation will occur is whether an article emerges from a process with a new name, character, or use different from that possessed by the article prior to processing. See Texas Instruments Inc. v. United States, 681 F.2d 778 (C.C.P.A. 1982). This determination is based on the totality of the evidence. See National Hand Tool Corp. v. United States, 16 C.I.T. 308 (1992), aff’d, 989 F.2d 1201 (Fed. Cir. 1993). Additionally, Section 304 of the Tariff Act of 1930, as amended (19 U.S.C. 1304), provides that unless excepted, every article of foreign origin imported into the United States shall be marked in a conspicuous place as legibly, indelibly, and permanently as the nature of the article (or its container) will permit, in such a manner as to indicate to the ultimate purchaser in the United States, the English name of the country of origin of the article. Congressional intent in enacting 19 U.S.C. 1304 was “that the ultimate purchaser should be able to know by an inspection of the marking on the imported goods the country of which the goods is the product. The evident purpose is to mark the goods so that at the time of purchase the ultimate purchaser may, by knowing where the goods were produced, be able to buy or refuse to buy them, if such marking should influence his will.” See United States v. Friedlaender & Co., 27 C.C.P.A. 297, 302 (1940). Part 134 of the U.S. Customs and Border Protection (“CBP”) Regulations (19 CFR 134) implements the country of origin marking requirements and exceptions of 19 U.S.C. 1304. Section 134.1(b), CBP Regulations (19 CFR 134.1(b)), defines “country of origin” as the country of manufacture, production, or growth of any article of foreign origin entering the United States. Further work or material added to an article in another country must effect a substantial transformation in order to render such o